Diagsheet

2018 Jeep Wrangler · recalls

2018 Jeep Wrangler recalls

NHTSA lists 14 recalls that include the 2018 Jeep Wrangler. The newest, 24V-676, was filed Sep 12, 2024 for the backup camera. 4 of them are on the transmission and drivetrain.

  • 14recalls
  • 8systems
  • 1,817owner complaints

Newest recall or investigation Sep 19, 2024 · checked Sep 22, 2026

Whether your car is included depends on its VIN, and a finished repair drops it off the list. Check yours at nhtsa.gov/recalls.

Every recall, newest first

24V-676Sep 12, 2024NHTSA 24V676000

Back Over Prevention: Sensing System: Camera

Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.

Remedy: Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.

3 of the 1,817 owner complaints on this car cite the backup camera. Symptom sheets that include this system: Infotainment, screen or backup camera fails (104).

24V-652Sep 5, 2024NHTSA 24V652000

Electrical System: Instrument Cluster/Panel

Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."

Risk: An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.

Remedy: Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.

266 of the 1,817 owner complaints on this car cite the electrical system, 6 of them the same part of it (Electrical System: Instrument Cluster/Panel). Symptom sheets that include this system: Infotainment, screen or backup camera fails (104) · Engine stalls or loses power while driving (94) · Multiple warning lights come on at once (67) · Check engine light or misfire (49).

23V-116Feb 23, 2023NHTSA 23V116000

Power Train:Clutch Assembly

Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

Risk: Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

Remedy: Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1-800-853-1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V-028. Vehicles previously repaired under recall 21V-028 will need to have the new remedy completed.

174 of the 1,817 owner complaints on this car cite the transmission and drivetrain, 4 of them the same part of it (Power Train:Clutch Assembly). Symptom sheets that include this system: Engine stalls or loses power while driving (94).

21V-028Jan 28, 2021NHTSA 21V028000

Power Train:Clutch Assembly

Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

Risk: Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

Remedy: FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.

174 of the 1,817 owner complaints on this car cite the transmission and drivetrain, 4 of them the same part of it (Power Train:Clutch Assembly). Symptom sheets that include this system: Engine stalls or loses power while driving (94).

20V-124Mar 3, 2020NHTSA 20V124000

Power Train:Clutch Assembly

Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

Risk: The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W12.

174 of the 1,817 owner complaints on this car cite the transmission and drivetrain, 4 of them the same part of it (Power Train:Clutch Assembly). Symptom sheets that include this system: Engine stalls or loses power while driving (94).

19V-680Sep 26, 2019NHTSA 19V680000

Seat Belts:Front:Anchorage

Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.

Risk: A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.

Remedy: FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.

9 of the 1,817 owner complaints on this car cite the seat belts.

19V-320Apr 23, 2019NHTSA 19V320000

Equipment

Erwin Hymer Group USA LP dba American Fastbacks (EHGUSA-AF) is recalling certain 2018 Jeep Wrangler vehicles sold with a roof top tent installed. The top cover of the roof top tent may crack or break, possibly resulting in the cover detaching from the vehicle while moving.

Risk: If the roof top tent cover detaches from the vehicle while moving, it can create a road hazard, increasing the risk of a crash.

Remedy: The remedy for this recall is still under development. The recall began May 9, 2019. Owners may contact American Fastbacks customer service at 1-844-533-7997 extension 301. Note: Vehicles in this recall are also included in recall 19V-190.

1 of the 1,817 owner complaints on this car cite the equipment.

18V-786Nov 8, 2018NHTSA 18V786000

Latches/Locks/Linkages:Doors:Latch

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler four-door vehicles. The right rear passenger door latch may not be in the correct location, possibly preventing the door from latching properly.

Risk: If the right rear passenger door opens unexpectedly, it can increase the risk of injury.

Remedy: Chrysler will notify owners, and dealers will repair the right rear door latch reinforcement, free of charge. The recall begin December 6, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UB6.

1 of the 1,817 owner complaints on this car cite the latches/locks/linkages.

18V-675Sep 28, 2018NHTSA 18V675000

Structure:Frame And Members

Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.

Risk: An unexpected reduction in steering ability, can increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UA5.

97 of the 1,817 owner complaints on this car cite the structure. Symptom sheets that include this system: Paint peels or body rusts (40) · Windshield cracks or distorts (27).

18V-524Aug 9, 2018NHTSA 18V524000

Electrical System:Wiring:Front Underhood

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.

Risk: A vehicle stall can increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.

266 of the 1,817 owner complaints on this car cite the electrical system. Symptom sheets that include this system: Infotainment, screen or backup camera fails (104) · Engine stalls or loses power while driving (94) · Multiple warning lights come on at once (67) · Check engine light or misfire (49).

18V-343May 25, 2018NHTSA 18V343000

Steering

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The intermediate steering shaft may not have been properly welded causing a split where the external spline is formed.

Risk: If the weld seam splits, the steering wheel may lose center positioning causing a loss of steering responsiveness and increasing the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect and, as necessary, replace the intermediate steering shaft, free of charge. The recall began June 21, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U48.

1115 of the 1,817 owner complaints on this car cite the steering system. Symptom sheets that include this system: Steering wheel shakes or the "death wobble" (517) · Power steering cuts out or goes heavy (116) · Steering sticks, feels notchy or jerks (42).

18V-332May 17, 2018NHTSA 18V332000

Electrical System:Wiring

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Risk: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

266 of the 1,817 owner complaints on this car cite the electrical system. Symptom sheets that include this system: Infotainment, screen or backup camera fails (104) · Engine stalls or loses power while driving (94) · Multiple warning lights come on at once (67) · Check engine light or misfire (49).

18V-280May 1, 2018NHTSA 18V280000

Power Train:Automatic Transmission

Chrysler (FCA US LLC) is recalling certain 2018 Dodge Charger, Durango and Challenger, Jeep Grand Cherokee and Wrangler, Chrysler 300, and RAM 1500 vehicles. An incorrect transmission park lock rod may have been installed in the transmission.

Risk: If the incorrect park lock rod is installed, the transmission may not shift into 'PARK' and keep the vehicle from moving, increasing the risk of unintended vehicle movement and the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will install the correct park lock rod, free of charge. The recall began June 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U43.

174 of the 1,817 owner complaints on this car cite the transmission and drivetrain. Symptom sheets that include this system: Engine stalls or loses power while driving (94).

18V-231Apr 12, 2018NHTSA 18V231000

Structure:Frame And Members

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The rear under body ladder rail may corrode, possibly reducing the strength of the rear floor pan and causing the left rear seat mount to become loose.

Risk: If the floor pan strength is reduced and/or the rear seat mount becomes loose, the rear seat may detach in a crash, increasing the risk of injury.

Remedy: Chrysler will notify owners, and dealers will inspect and, as necessary, coat the interior and exterior of the driver's side rear underbody ladder rail with three-part rust protection. The recall began September 11, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U27.

97 of the 1,817 owner complaints on this car cite the structure. Symptom sheets that include this system: Paint peels or body rusts (40) · Windshield cracks or distorts (27).

Complaints with no recall behind them

The systems owners of the 2018 Jeep Wrangler complain about most that none of these recalls covers, as of Sep 22, 2026. A problem can be widespread without being a safety defect NHTSA can order fixed.

NHTSA investigations

EA21-002opened Sep 17, 2021
Airbags · model years 2007 to 2018

Desiccated air bag inflator rupture. Open.

NHTSA summary
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been n
PE19-012opened Sep 16, 2019
Steering · model years 2018 to 2019

Frame weld deficiencies. Closed oct 29, 2023.

NHTSA summary
On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI decided to include reports of steering shimmy or wobble, loose steering, and steering stiction (loss of power steering) as part of this investigation and parent petition (DP18-004). ODI received information from the vehicle manufacturer Fiat Chrysler Automobiles (FCA) via information request letters dated March 8, 2019, and February 6, 2020. Supplemental requests for information occurred between July 2020 and July 2023. A review of the responsive manufacturer information showed that vehicles presenting an unexpected reduction in steering ability due to a welding tool misalignment were correctly addressed via recall 18V-675. General complaints concerning the weld appearance were not associated with a realized risk to motor vehicle safety. ODI identified a limited number of reports involving weld separation on vehicles that were out of scope of recall 18V-675. FCA identified various causes of weld quality issues in early production (build dates prior to March 2018) including improper welding techniques on galvanized frames and component part variation leading to off-seam welds. These is
PE19-008opened Jul 29, 2019
Seat Belts · model years 2011 to 2018

Seat belt buckle bracket failure. Closed dec 12, 2019, led to recall 19V-680.

NHTSA summary
On July 17, 2019, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 19-008 after receiving three Vehicle Owner Questionnaire (VOQ) reports alleging the driver's side seat belt buckle separated from the seat frame, rendering the seat belt non-functional. The VOQs involved model year (MY) 2015 and 2016 Jeep Wrangler (JK platform) that were configured for right-hand drive (RHD) use. On August 8, 2019, ODI issued an information request (IR) letter to FCA.The scope of the IR included all JK Wrangler produced for sale in the U.S. (both left- and right-hand drive), and amongst other things, requested any reports or allegations of driver's seat belt bracket failures on these vehicles. In its review of FCA's response, ODI determined that approximately 1.7 million JK Wrangler were produced from MY 2007 to 2018, about 16,000 of which were configured for RHD. ODI notes that the RHD Wrangler are typically used for rural postal delivery which often experience a more severe duty cycle. Also RHD JK was was not produced in MY 2007.As explained in the IR response, FCA identified three distinct populations of JK Wrangler concerning the driver's seat belt bucket bracket; specifically the MY 2007-2018 LHD (~1.7M units), the MY 2008-2010 RHD (4,563 units), and the MY 2011-2018 RHD (11,463 units) populations.FCA provided details on the designs used in each of these populations, identifying specific differences deemed pertinent to the strength and durability of each un
EA19-001opened Apr 19, 2019
Airbags · model years 2010 to 2018

Electrical overstress. Closed sep 19, 2024, led to recall 20V-024.

NHTSA summary
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles
DP18-004opened Nov 16, 2018
Steering · model years 2018 to 2019

Frame weld deficiencies. Closed sep 17, 2019.

NHTSA summary
In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) opened a Defect Petition (DP18-004) to evaluate whether to grant or deny the petition. On March 8, 2019, ODI sent an Information Request letter to Fiat Chrysler Automobiles (FCA) requesting information on frame weld related issues on all MY 2018-2019 Jeep Wrangler 'JL' vehicles. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI opted to include a request for additional information concerning reports of steering shimmy or wobble, loose steering, and steering lockup in the March request letter. ODI has performed a preliminary analysis on the information obtained from FCA. Based on ODI's review of the applicable materials, NHTSA has decided to grant the petition. While reviewing the applicable materials obtained from the manufacturer, ODI identified various reports and references to frame welded component detach

More on the 2018 Jeep Wrangler

Problems by mileage on the 2018 Jeep Wrangler · Jeep Wrangler years to avoid

Recalls on other model years

20144201532016520175201814201992020122021152022152023142024112025420263