Brake pedal feels soft or spongy

Risk: A brake fluid leak will increase brake pedal travel and extend the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy: Dealers will replace the front brake hoses, free of charge. Owner notification letters were mailed June 27, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S12.

Risk: A separated brake pedal bumper can cause the brake lights to illuminate continuously, causing confusion to other drivers and increasing the risk of a crash. On automatic transmission vehicles, a missing brake pedal bumper can allow the driver to shift the vehicle out of the "PARK" position without depressing the brake, allowing the vehicle to rollaway, increasing the risk of injury.
Remedy: Dealers will replace the brake pedal bumpers and clutch pedal bumpers, free of charge. Interim owner notification letters notifying owners of the safety risk were mailed on March 4, 2022. Owner notification letters were mailed on June 13, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S02.

On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturing on certain MY 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The result causes a brake fluid leak, lengthening the distance needing to stop the vehicle, increasing the risk of a crash.On March 10, 2023, Ford Motor Company (Ford) submitted to NHTSA Safety Recall 23V-162 (Ford Recall 23S12) to address front brake jounce hoses that may rupture. Ford found the rupture occurs from a localized failure of the internal reinforcement braid due to cyclic fatigue through tensile/bending and torsional inputs during suspension and steering articulations. The supplier for the front brake jounce hoses is Hitachi. This recall affects the subject vehicles equipped with non-hybrid engines and the suspect front brake jounce hoses (a total of 1,280,726 vehicles). The recall covers subject vehicles built from February 3, 2012 to July 19, 2017 when the suspect hoses were used in vehicle production.

On April 18, 2018, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA) 18-002 to investigate reports of braking concerns in model year (MY) 2006-12 Ford Fusion and Lincoln MKZ, and MY 2006-11 Mercury Milan vehicles manufactured with Continental Automotive System?s ABS hydraulic control units (HCUs). Complainants report that after an ABS braking event (initiated by slippery or uneven surfaces) the brake pedal moved towards the floor and the vehicle stopping distance increased beyond driver expectations.Inside the HCU are four hydraulic normally closed (NC) valves with zinc-coated moving armatures that control the flow of brake fluid. Unstable brake fluid can degrade over time, allow the brake fluid to gel, and corrosion to form on the armatures. The high-viscosity gelation and corrosion can cause the armatures to become stuck (open). In some cases, braking returns to normal when the armature(s) subsequently become unstuck. The intermittent condition proves difficult to diagnose with complainants reporting having (non-HCU) repairs conducted only to have the condition return.During the investigation, 14 HCUs from complaint vehicles were recovered, including seven from reported crashes. NHTSA?s Vehicle Research and Test Center (VRTC) disassembled the HCUs, removed the four NC valves in each, and confirmed 22 of the 56 NC valves contained stuck armatures. On seven of the 14 HCUs, both front wheel armatures were stuck, on nine of the 14 HCUs two or three arma

On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes